Used Howden Refrigeration Equipment, Air Compressors, and Countertop Ice Makers: How I Decide What's Worth Buying

Why I stopped handing out one-size-fits-all equipment advice

When I took over facilities purchasing in 2020, I assumed the job was mostly about finding the lowest quote and getting it approved before the month closed. Four years and a few hundred purchase orders later, I can tell you the hardest part isn't the buying. It's figuring out which kind of purchase you're actually making.

A $200 countertop ice maker for the breakroom and a used Howden refrigeration unit for a process line are both 'equipment,' but they have almost nothing in common from a purchasing standpoint. Treat them the same way and you'll either over-engineer the small stuff or under-scrutinize the big stuff. Both are expensive mistakes, just in different currencies.

So here's how I break it down now. Three scenarios, three different playbooks.

Scenario A: Breakroom and office gear (countertop ice makers, electric heaters)

This is the category where the purchase price genuinely matters least—and that surprises people. A cheap countertop ice maker that's a pain to clean will cost you more in labor and replacement than a slightly pricier model that comes apart easily. I learned that the hard way in 2022, when we went through two $180 units in eighteen months because nobody wanted to deal with the cleaning routine (and honestly, I don't blame them—the reservoir had corners you couldn't reach with a normal brush).

If you're wondering how to clean a countertop ice maker without turning it into a weekend project: unplug it, drain the reservoir, run a 1:1 white vinegar and water cycle, then two plain-water cycles, and wipe the evaporator plate and bin by hand. Most manuals say monthly. We aim for every six weeks and usually hit every eight (ugh).

Here's something vendors won't tell you: the 'self-clean' button on most countertop units only flushes the water lines. It does nothing for the evaporator plate or the storage bin, which is where the actual grime lives. If cleaning access is bad, the machine will get skipped, and a skipped machine is a broken machine waiting to happen.

Same logic applies to electric heaters for office spaces. I look for UL or ETL certification, a tip-over switch, and a thermostat that actually holds a setpoint instead of cycling wildly. The $40 difference between a no-name unit and a certified one is the cheapest insurance you'll buy all year. Prices for countertop ice makers as of early 2025 run roughly $150-400 depending on capacity and cleaning design (based on quotes from three vendors; verify current pricing).

My rule for Scenario A: if the item costs less than a few hundred dollars and fails without stopping production, optimize for ease of maintenance and safety certification, not for the lowest line item.

Scenario B: Production-floor air (compressors and fans)

This is where total cost of ownership starts to bite. An air compressor or an industrial fan can have a purchase price that's 15-20% of its lifetime cost—the rest is energy, maintenance, and downtime. A cheaper unit with a lower efficiency rating can erase its savings in electricity within a couple of years, depending on duty cycle.

According to the U.S. Department of Energy (energy.gov), compressed air systems account for roughly 10% of industrial electricity use in the U.S., and leaks alone can waste 20-30% of a system's output. That's not a rounding error. Before we replaced anything, I had our maintenance lead walk the line with an ultrasonic leak detector. We found eleven leaks we didn't know about. Fixing those cost less than $600 in parts and dropped our compressor run time noticeably.

On the fan side, this is where Howden comes up in our conversations. The Howden fan company has been building industrial fans and blowers since 1854 (howden.com), and their range covers everything from heavy-duty process fans to smaller air-handling units. What I care about as a buyer isn't the brand history—it's whether the specific model's efficiency curve matches our actual operating point. A fan that's highly efficient at 100% load but runs at 60% most of the time may not be the right choice. Ask for the performance curve at your expected duty point, not just the headline number.

A counterintuitive thing I've learned: buying a larger compressor 'for headroom' often raises TCO, because part-load efficiency drops and you're paying to compress air you vent through leaks. Size to your measured demand, not to your worst-case guess.

Scenario C: Capital equipment and used Howden refrigeration systems

Now we're in the deep end. Used Howden refrigeration equipment can be a genuinely smart buy—the underlying hardware is robust and the installed base is large—but the due diligence burden is completely different from buying new. You're not just evaluating the machine; you're evaluating its history, its remaining life, and whether you can keep it running for another decade.

What most people don't realize is that the seller's 'low hours' claim is basically unverifiable unless you get service logs and a compressor run-hour meter reading. I've seen listings where the hour meter had clearly been replaced. Ask for maintenance records, oil analysis if available, and the original nameplate data. If the seller can't produce them, price that uncertainty in—or walk away.

The surprise for me wasn't the equipment cost. It was the installation and commissioning line. Rigging, new piping, electrical work, refrigerant charge, and controls integration added roughly 40% to the sticker price on one quote we reviewed. When you stack that against a new unit with a warranty, the used option isn't automatically cheaper. It's cheaper if—and only if—you have the in-house expertise to spec the install and the spare-parts plan.

Also: refrigerant compliance isn't optional. Under the U.S. EPA's AIM Act, HFC phasedown schedules affect which refrigerants you can realistically service long-term. Before committing to any used refrigeration system, confirm the refrigerant type and check whether your service contractors can still source it at a reasonable cost. The same caution applies in the EU under the F-gas Regulation (EU 517/2014). Verify current rules with your regulator—I'm a purchasing person, not a compliance attorney.

My rule for Scenario C: used equipment is a maintenance and engineering decision first, a financial decision second. If you don't have the technical bench to support it, the savings are theoretical.

How to figure out which scenario you're in

Three questions, in this order:

  1. What does an hour of downtime cost? If the answer is 'nothing, people just use the other breakroom,' you're in Scenario A. If it's measured in thousands, you're in B or C.
  2. Do you have in-house maintenance? If yes, used capital equipment becomes more viable. If no, warranty and service network matter more than purchase price.
  3. Is this a convenience purchase or a production asset? Convenience purchases should be cheap, safe, and easy to clean. Production assets should be specified against duty cycle and supported for their full life.

There's something satisfying about finally getting this framework into a one-page decision guide for our team. After two years of ad-hoc purchases and a few painful surprises, we now route every request through those three questions before anyone opens a vendor portal. The best part: our finance team stopped asking me why the 'cheap' option wasn't chosen.

One caveat, because I can only speak to my own situation: this worked for us as a 400-person manufacturer with a small but capable maintenance team and fairly predictable demand. If you're a seasonal operation with demand spikes, or a tiny office with no maintenance staff at all, the calculus shifts—probably toward leasing or service contracts rather than ownership. Your mileage may vary.

Look, none of this is glamorous. But the difference between a $200 ice maker that lasts three years and one that lasts eight, or between a used chiller that runs and one that eats your maintenance budget, usually comes down to asking the right questions before the purchase order goes out—not after.

Share
author-avatar

Elisa Nordberg

Elisa Nordberg writes about air-cooled and water-cooled industrial chillers, modular glycol systems, and screw, scroll, and centrifugal configurations for process and comfort cooling. Her evaluations reference ISO 5149 and AHRI 550/590 practices while comparing cooling capacity, COP, IPLV, compressor lift, fluid flow, and evaporator approach temperature. She helps plant engineers and sourcing teams size dependable chiller packages, interpret part-load performance, and balance energy use, redundancy, maintenance access, and lifecycle cost.

Leave a Reply

Your email address will not be published. Required fields are marked *